Establishing and Configuring IP Settings on Sealevel 170PoE-ROHS and 170E-ROHS Modules

The Sealevel 170PoE-ROHS and 170E-ROHS are Ethernet-based I/O modules used with MachineMetrics for reliable data collection from sensors, switches, and machine signals.
When setting up a new module or reconfiguring an existing one, the SeaMAX Ethernet Configuration Tool can be used to establish or restore network communication and assign a static IP address for stable operation.

This guide explains how to install the SeaMAX tool, use the Recover Device function (the preferred configuration method), and verify communication. It also includes alternate setup and factory reset options for field recovery.

Model Differences

• 170PoE-ROHS – Powered through Ethernet via IEEE 802.3af PoE (Class 0, ≤ 3.5 W).
• 170E-ROHS – Requires a 12–24 VDC external power supply via the terminal block.
Both models use the same network configuration process.

Feature Availability

How It Works

The SeaMAX Ethernet Configuration Tool communicates directly with Sealevel I/O modules over the local network.
When a module is unconfigured, unreachable, or on an unknown subnet, the Recover Device function re-establishes communication by MAC address — no IP address is required.
Once communication is established, a static IP can be assigned to maintain consistent connectivity with MachineMetrics Edge devices.

How to Use It

Download and Install the SeaMAX Ethernet Configuration Tool

• Download the official SeaMAX Software Suite from Sealevel’s website.
• Run the installer and follow the prompts to complete setup.
• After installation, launch the SeaMAX Ethernet Configuration Tool from the Start Menu.

Preferred Method — Recover Device and Configure a Static IP

This is the fastest and most reliable way to bring a Sealevel 170-series module online.

1. Open the SeaMAX Ethernet Configuration Tool.

2. Click the Recover Device button.

3. In the MAC Address field, enter the MAC address printed on the back of the device (see image below).
    

   

4. When entered correctly (using dashes), the indicator will turn green.

5. Click Recover.

6. A confirmation pop-up will appear — dismiss it.

7. Click Search for Devices — the module should now appear in the list.

8. Select the device from the list.

9. Choose DHCP to temporarily assign an IP, or manually enter a Static IP Address, Subnet Mask, and Gateway as defined by your IT network.

10. Click Apply to save the configuration.

11. The module will refresh briefly, and the new network settings will take effect.

Alternate Setup Methods (Optional)

Direct Static Configuration
Use when you already know the IP address to assign.
• Connect your PC directly to the module using a PoE switch or injector.
• Set your PC NIC to:
– IP Address: 192.168.42.254
– Subnet Mask: 255.255.255.0
– Gateway: none
• Launch the SeaMAX tool and search for devices.
• The module will appear at its default IP 192.168.42.253.
• Select the device, enter your desired static network settings, and click Apply.

Enable DHCP
Use when your network automatically assigns IP addresses.
• Follow the same connection steps above to locate the device at 192.168.42.253.
• Check Enable DHCP Configuration and click Apply.
• The module’s LEDs will blink while seeking a lease and turn solid when complete.
• Click Search for Devices again to view the new IP.

Factory Reset Options

Soft Reset (via SeaMAX Tool)
• Use the Recover Device button and enter the MAC address.
• The tool re-flashes the network settings and restores DHCP communication without affecting I/O configuration.

Hard Reset (Internal Button — Factory Default Restore)
⚠ Caution: The factory reset button is located inside the device enclosure and requires removing the back cover. Only qualified personnel should perform this procedure when software recovery is not possible.

1. Disconnect power to the module. For PoE models, unplug the Ethernet cable. For non-PoE models, disconnect the external DC supply.

2. Using a screwdriver, remove the four screws on the back of the module and carefully lift off the cover.

3. Locate the recessed RESET button on the circuit board near the RJ-45 port.

4. Press and hold the button.

5. While holding RESET, restore power to the device (reconnect Ethernet or DC supply).

6. Continue holding RESET for approximately 10 seconds, until the LEDs flash.

7. Release the button — the device will reboot to its factory static IP: 192.168.42.253.

8. Reinstall the back cover and secure the four screws.

LED Indicators

The front panel LEDs provide visual feedback during power-up, configuration, and normal operation.

Tip: During DHCP recovery, LEDs blink while searching for a lease and turn solid once connected.

Tips & Best Practices

• Always use dashes when entering the MAC address (e.g., 00-0A-1B-2C-3D-4E).
• Coordinate with IT before assigning static IPs to prevent conflicts.
• Label each module with its configured IP for future reference.
• Run the SeaMAX tool from the same subnet as the Sealevel device.
• Use DHCP only for initial discovery — assign a static IP for permanent deployment.
• Ensure modules are properly powered (PoE or 12–24 VDC) before configuring.

FAQs & Troubleshooting

Q: The MAC address entry does not turn green.
A: Ensure it is entered with dashes and includes all 12 hexadecimal characters.

Q: The device does not appear after recovery.
A: Rescan and verify your PC network adapter is on the same subnet.

Q: The LEDs blink indefinitely after enabling DHCP.
A: No DHCP server is available — verify switch or VLAN connectivity.

Q: Is the I/O configuration lost after recovery or reset?
A: No, network resets do not affect I/O channel configurations.

Q: Can I establish multiple devices at once?
A: No, each module must be configured individually by MAC address.

Related Articles

• Installing a Part-Count Proximity Sensor with Sealevel 170POE-ROHS
• Troubleshooting Guide- Machine Not Reporting
• Edge Device and Network Diagrams